1/4 yard of fabric (either a regular 1/4 yard cut, or a fat quarter works great)
contrasting fabric for the pocket
small zipper (It’ll be cut down to 4.5 inches- I used a 7 inch zipper because that’s what I had)
white, black, and red felt or fleece
disappearing ink or water soluble ink fabric marking pen
wonder under or similar fusible backing (Get the sewable kind! I didn’t, I used the ultra hold and ended up having to hand stitch instead of machine stitch)
pattern- download here <<< Click for pattern
*(all seam allowances are approx. 3/8 inch- I use the edge of my presser foot)
- First cut out your pattern, pin it to the fabric, cut out fabric, and iron on wonder under to the backs of the eye pieces (leave the paper backing on for now.)
- Starting with your leg pieces, sew with right sides together, down the sides and around the bottom curve. Leave the top open for stuffing. Notch the rounded edge.
- Iron the legs to smooth them out. Stuff them with fiberfill. Set them aside for now.
- Peel the paper backing off the wonder under on the eye pieces. Iron them to the body placing the white part about 1 inch down from the center and 2 inches from either edge.
- Stitch around both eye pieces to secure them in place, and to add a little detail. Machine or hand stitch. I was able to machine stitch one, but then ran into troubles after that and gave in to hand stitching the rest. I’m pretty sure this was because I used fusible backing that is no-sew, so it’s extra strong and gunks up the machine. I knew it was a no-no, but tried anyway. Don’t do it. Follow the instructions on whatever kind you buy.
- Grab your zipper. Unzip it just a little bit and tack it just past the metal stopper parts.
- From the metal beginning part (so technical- I know…) of the zipper, measure 4.5 inches and tack the zipper just barely past that. Cut the zipper just a little past the tack.
- Now we’re going to make our zipper hole. Take one of your pocket pieces, place it right side up. Draw a box that is 4 1/2 inches wide and 1/4 inch tall. It will 7/8 inch down from the top and 3/4 inch from either edge. (I’m pretty sure it ends up being 4 1/2 inches, but just in case, just measure from the sides and draw your line and it’ll work.) Inside the box, mark a point in the center that is 1/4 inch from either edge of the box. Draw a diagonal line from there to each corner. Then draw a line connecting those two points. I know I didn’t describe that well. It should look like it does in the picture when you’re done. Pin the pocket piece in place approx. 3/8 inch above the bottom of the body piece.
- Stitch around the box you drew.
- Cut on the inner lines. At the end triangles, cut up to the corners where you sewed, but be super careful not to cut through the stitching!
- Push the pocket piece through the hole and press as flat and neat as you can. (Front and back views shown)
- Take your other pocket piece and on the right side make a mark 3/4 inch down and centered. I folded the piece in half to find the center.
- On the tongue piece there is a part that straightens out on the top. Fold this part down, like in the picture. Line up the top of the tongue, where the fold is, with the dot you just made on the pocket piece. Sew the tongue on using a zig-zag stitch.
- Hand stitch a few stitches onto the center bottom of the tongue to add a little detail.
- Baste the teeth onto the zipper however you want to place them.
- Place the zipper in the hole you cut out a few steps back. Using a zipper foot, topstitch around the edge of the zipper to secure it in place. Be sure not to sew over the teeth!
- Turn the body piece over and with right sides together, line up your other pocket piece with the one that is stitched to the zipper. Sew a 3/8 inch seam all around. Now you have a zipper pocket!
- Pin or baste the legs (approx. 1 1/4 inches from the edges) onto the front body piece. I pinned in the picture, but after making a few switched to basting and liked that better. Just don’t forget to shorten your stitch length after basting- I did that one too many times.
- With right sides together, sew the back body piece to the front piece. Be sure to leave an opening a few inches wide so you can turn it right side out (mine is where the leg is sticking out.) Clip the corners and notch the curve.
- Turn it right side out.
- Stuff your monster.
- Hand stitch the opening closed. I don’t know what the stitch I’m using is called. It’s the same stitch I use to sew on binding onto a quilt. Slip the needle into the top of the crease and pull through. Then directly across it on the other side do the same thing. So where your needle left the fabric will line up with where your needle enters the fabric on the other side, so you’re moving in a forward motion. Confusing? Yeah, sorry.
- Now you’re done! Yay!